Window surrounds and pilaster strips
Window surrounds and pilaster strips are among the most used elements of façade décor for the exterior façade. These façade profiles are mounted around the window and are suited for restoration of old buildings as well as for insulated façades.
Our window surrounds are very easy and quick to mount. They only need to be painted with the desired façade paint after completion. It is possible, of course, to adjust the window surrounds’ forms and sizes according to your needs as well.
The window surrounds described above are often combined with a windowsill cornice (window ledges). These window ledges are mounted below the windowsill and are also suited for renovation of old buildings and insulation façades.
The length of a window ledge always results from the clear span of the window plus the width of both window surrounds left and right (e.g. clear span: 130cms, surround width: 12cms (2x) = length of window ledge 154cms). Please observe that the used windowsill’s width will have approximately 2cms overhang.
Another possibility to combine window surrounds and windowsill cornices presents the cap stone (sometimes center stone or header as well). The header cuts the surround above the lintel right at the center and accentuates the window by its superior position.
The cap stone mounting is very easy as well, and the center stone is painted with the desired façade paint after completion, too. Of course, we can also custom-build this façade element according to your specifications of form and size.
Roof or eaves cornices are also a very common element of façade décor and are mounted right below the eave on the closed lower ceiling and wall. Eave cornices are suitable for both restoration of old buildings and insulated façades.
It takes only a few steps to mount cornices and we also offer the possibility to precut the outer and inner corners. The eaves cornices only need to be painted with the desired façade paint after mounting. We also customize the cornices upon request.
Quoins are also a very common element of exterior façade décor. These are mounted at the façade’s corners and present the perfect supplement for façade design with window surrounds, eaves cornices, and cap stones.
Corner cladding quoins are favorable with regard to mounting in particular as they need not be glued together – as opposed to ornamental cladding tiles. The corner cladding quoins only need to be painted with the desired façade paint after mounting. Also the corner cladding quoins can be custom-made to your individual desired form and size upon request.
Ornamental cladding tiles
Ornamental cladding tiles are used for the visual design of the façade’s corners just like corner cladding quoins. Ornamental cladding tiles and corner cladding quoins start at the ground floor and are mounted up to the lower edge of the eaves cornice. We will gladly help in case of doubt or additional need for information.
Ornamental cladding tiles are an economic alternative to corner cladding quoins as the corners need to be glued together on site. The mounting of the ornamental cladding tiles is very easy as well, and the cladding tiles are painted with the desired façade paint after completion, too.
Exterior column cladding
Reinforced concrete columns are often made using the most simple formwork. These columns are then visually upgraded in the course of the façade design by means of elements of décor for top (capital or header) and bottom (base or footer).
Our column claddings always consist of 2 half-shells which are mounted on the existing columns. Also these elements of décor can be custom-made according to your specifications if you need them in a certain specific width or height.
Interior column cladding
Also interior columns may be cladded, of course. However, the headers’ and footers’ surface coating differs from the one used for exterior application. As no weatherproof coating is required, these are coated with top-quality white dispersion paint.
The interior column claddings also consist of two half-shells which are mounted on the existing columns. The column claddings can be custom-made to your individual desired form and size upon request.
Individual custom-made columns
Entire columns, i.e. column claddings including the column shaft, are available upon request as well, of course. Diameter and height can be freely varied; however, the maximum diameter is approx. 2.00 meters, but the height is basically limitless due to the modular design.
In the past we already produced columns in a shape of vase with 1.45m diameter and 9.0 meters height. We will gladly help in case of additional need for information.